QL355P 英國TTi 可編程直流穩壓電源
QL355P 英國TTi 可編程直流穩壓電源
*的直流電源，單路或三路輸出
每個輸出高達 112 瓦
非常高的精度、非常低的噪音、出色的動態
帶有數字和旋轉控制的高級用戶界面
多個電壓/電流范圍提高靈活性
用于電源設置的多個非易失性存儲器
可切換遠程感應提供的負載調節
全面保護，包括 OVP 和 OCP 跳閘
工作臺占地面積緊湊；用于機架安裝的模塊化寬度
輔助輸出在 3A 電流下可變 1.00V 至 6.00V，具有可選擇的電壓和電流計量（T 型號）
通過 USB、RS232、GPIB 或 LAN（P 型號）進行總線編程
LAN 接口符合 LXI 標準
后部有重復的電源和感應端子（P 型號）
QL355P英國TTi直流穩壓電源的主要介紹
The QL Series II is the latest and highest performance linear regulated power supply series from TTi.
Single and triple output models are available. Each model can be specified with or without digital remote control interfaces.
Each main output provides more than 100 watts of power, and dual range capability offers higher currents at lower voltages.
New features include an enhanced auxiliary output with fully variable voltage and higher current capability on T models, and an LXI compliant LAN interface on all P models.
Despite the improvements in high frequency switcher design, Linear regulation still offers the lowest output noise and the best transient response （recovery time from a sudden current step）. It also offers the most benign stability characteristics when driving complex load conditions. |
| Ultra-low noise |
Most linear regulated power supplies offer low output noise with figures below 2mV rms being typical. The QL series goes a stage further with an RMS noise figure of 0.35mV and tightly specified pk-pk noise. Many higher power linear regulated designs include a line frequency switched pre-regulator. Whereas this may not compromise differential output noise, it significantly increases common mode noise currents. The QL Series uses true linear regulation without any line frequency switching regulation. Consequently it offers exceptional common mode noise levels of<4uA rms at 20MHz bandwidth. |
QL355P英國TTi直流穩壓電源的主要介紹
| Higher Currents at Lower Voltages |
The QL series provides multiple ranges for increased current capability at lower voltages. For the QL355, the main range offers 0 to 35 volts at up to 3 amps. The higher current range provides up to 5 amps for voltages up to 15V. The QL564 has a main range of 0 to 56 volts at up to 2 amps. The higher current range provides up to 4 amps for voltages up to 25V On both models, a further low current range provides an enhanced current setting and measurement resolution of 0.1mA. |
Voltage and current are controlled using instrumentation quality 16 bit DACs enabling voltages to be set to 1mV resolution even at full output. Indeed, the accuracy is sufficient for the QL to be used as a calibration source for some hand-held DMMs. |
| Why do I need a precision PSU ? |
Every engineer needs to have confidence in their equipment. A power supply is one of the most fundamental of bench instruments. You need certainty that the voltage you apply to a circuit is precisely what you want it to be. You need certainty that the output of your power supply is clean and stable. You need the ability to define a precise voltage at the load and maintain regulation independent of lead resistances. |
|
|
